Home»Products »General AC Drive » ALPHA6000S Series Open Loop Vector Control AC Drive

ALPHA6000S Series Open Loop Vector Control AC Drive

ALPHA6000S series AC drive is a high-performance product under open loop vector control mode. Adoption of the international leading technology of current vector control and torque control allows this product to really achieve the decoupling of AC motor and control manner of DC motor. The superior control attributes of our product can fully satisfy the motion drive requirements of our customers.

Technical Characteristics

Input voltage fluctuation range is ±20%.

Built-in RS485 communication supports MODBUS-RTU protocol.

Flexible frequency mix-given function

Multiple programmable I/O terminals

Abundant fault-protection and running-monitor functions

Support a range of extention cards including I/O,communication card, and more.

Three control modes including V/F control, Non-PG vector control, and V/F separation control.

V/F Control
It features superior control performance of vector control. Also, it is insensitive to motor parameters.
Start Torque 0.5Hz/ 150% rated torque
Speed Range 1:100
Steady-State Precision ±0.5%
It can control the motor to run stably with 150% rated torque at 0.5Hz.
Non-PG Vector Control (Open Loop Vector Control)
Independent current loop control guarantees the real torque control. It supports the immediate switching between torque control mode and speed control mode.
Start Torque 0.5Hz/ 180% rated torque
Speed Range 1:200
Steady-State Precision ±0.5%
Torque Precision ±5%
Torque Response ﹤20ms
It can control the motor to run smoothly with 150% rated torque at 0.5Hz.

Superior Control Properties

0.1s acceleration-deceleration under rated torque is attainable.
No sudden change or oscillation occurs in current phase when motor rotation reverses at zero speed.
Mains voltage is under stable control. Quick and reliable brake is available at deceleration even without dynamic brake.

Trip-Free Running

Advanced current and voltage control technology allows the AC drive to run stably without trip when alternatively accelerated and decelerated in 0.1s command.
Due to strong load capacity, the AC drive can work continuously for 20s with 180% rated load, and 1min with 150% rated load.
The AC drive offers smooth operation with large torque at low frequency under vector control mode.

Unique treatment to instantaneous power-failure

Extraordinary torque tracking function

Without special hardware detection circuit or function code setup, the AC drive can recognize motor speed, rotation, and phase angle in 0~60Hz within0.2s. It also provides smooth tracking start of freely rotating motor.

Industry Applications

The open loop vector control AC drive can be used in various industries including the wire drawing machine, film winding machine, coating machine, CNC machinery, knitting machine, jacquard machine, fan, water pump, chemical fiber, textile, synchronous linkage, injection molding machine, rolling mill, paper making line, etc.

Technical Specification of ALPHA6000S

Item Specification
Power Range 380V ±20% three phases: From 0.75 to 500kW
Rated Input Voltage and Frequency 380V three phases: 50/60Hz
Allowable Input Voltage Range 380V three phases: From 304 to 456V, Voltage unbalance rate of less than 3%, Frequency fluctuation of below ±5% 
Rated Output Voltage From 0 to rated input voltage
Max. Overload Current G model: 150% for one minute, 180% for 20 seconds
Control Method V/F control, Open loop vector control
Frequency Range From 0.00 to 650.00Hz (from S21R5GB to 3004GB)
From 0.00 to 400.00Hz (from 35R5GB/37R5PB to 3500G)
Frequency Accuracy Digital command ± 0.01% (from -10℃ to +40℃)
Simulation command ± 0.01% (25℃ ± 10℃)
Preset Frequency Resolution Digital command 0.01Hz
Simulation command 1/1000 of the maximum frequency
Output Frequency Resolution 0.01Hz
Preset Frequency Signal From 0 to 10V, From 0 to 20mA
Acceleration-Deceleration Time From 0.1 to 3600 seconds (The acceleration and deceleration time can be preset separately.)
Braking Torque The additional braking resistance reaches up to 125%.
Voltage-Frequency Characteristics Four kinds of fixed V/F characteristics are selectable.
Any V/F characteristic can be preset.
Protective Functions Over-voltage, under-voltage, current limit, over-current, overload, electronic thermal relay, overheating, over-voltage stall, load short circuit, grounding, under-voltage protection, input phase loss, output phase loss, short circuit to ground, interphase short circuit, motor overload protection, etc
Ambient Temperature From -10℃ to +40℃
Humidity From 5 to 95% RH (No condensation)
Storage Temperature From -40℃ to +70℃
Service Place Indoor (without any corrosive gas)
Installation Site The altitude is at most 1,000m. There is not any dust, corrosive gas, or direct solar radiation.
Vibration Less than 5.9m/s2 (0.6g)
Protection Rating IP20
Cooling Method Natural cooling or forced air cooling

ALPHA6000S Model Selection

Voltage Classes Model Motor Power (kW) Rated Output Current (A)
380V Three Phases 6000S-3R75GB 0.75 2.5
6000S-31R5GB 1.5 4
6000S-32R2GB 2.2 6
6000S-3004GB 4 9
6000S-35R5GB 5.5 13
6000S-37R5GB 7.5 17
6000S-3011GB 11 25
6000S-3015GB 15 32
6000S-3018G 18.5 37
6000S-3022G 22 45
6000S-3030G 30 60
6000S-3037G 37 75
6000S-3045G 45 90
6000S-3055G 55 110
6000S-3075G 75 152
6000S-3093G 93 176
6000S-3110G 110 210
6000S-3132G 132 253
6000S-3160G 160 304
6000S-3185G 185 342
6000S-3200G 200 380
6000S-3220G 220 426
6000S-3250G 250 480
6000S-3280G 280 520
6000S-3315G 315 600
6000S-3355G 355 680
6000S-3400G 400 750
6000S-3500G 500 900

Overall Dimension of ALPHA6000S Series Open Loop Vector Control AC Drive

Model H H1 W W1 D D1 D2 D3 d
6000S-3R75GB 180 169 115 105 150 158 85 120 4.5
6000S-31R5GB
6000S-32R2GB
6000S-3004GB 195 173 130 108 157 167 100 130 4.5

Model H H1 W W1 D D1 D2 d
6000S-35R5GB 270 255 190 175 176 186 122 7
6000S-37R5GB

Model H H1 W W1 D D1 D2 d d 1
6000S-3011GB 373 360 235 200 176 188 125 7 12
6000S-3015GB
6000S-3018G 420 405 270 200 218 230 175 7 14
6000S-3022G
6000S-3030G 503 488 311 200 230 242 180 7 14
6000S-3037G
6000S-3045G 590 570 351 200 254 266 192 10 20
6000S-3055G
6000S-3075G 698 672 400 280 260 272 186 12 22
6000S-3093G
6000S-3110G 850 823 505 420 280 292 212 12 22
6000S-3132G

Installation Size of 380V 160-355kW Three-Phase Standard Model with Base

Model W1 W2 W3 H1 H2 D1 D2 D3 d 1 d 2
6000S-3160G 600 200 530 1380 1360 400 280 60 3-φ 14 4-φ 14
6000S-3185G
6000S-3200G
6000S-3220G
6000S-3250G 800 300 730 1535 1515 410 288 60 3-φ 14 4-φ 14
6000S-3280G
6000S-3315G
6000S-3355G

Installation Size of 380V 160-355kW Three-Phase Standard Model with Wall Mount

Model W1 W2 H1 H2 D1 D2 D3 d 1
6000S-3160G 600 200 1026 1360 400 245 77 6-φ 14
6000S-3185G
6000S-3200G
6000S-3220G
6000S-3250G 800 300 1180 1515 410 250 88 6-φ 14
6000S-3280G
6000S-3315G
6000S-3355G

Installation Size of 380V 400-500kW Three-Phase Standard Model

Model W1 W2 W3 H1 D1 D2 D3 d 1
6000S-3400G 1000 700 900 1800 480 300 80 4-φ 22
6000S-3500G

Installation Size of 380V 160-500kW Three-Phase Narrow-Body Model

Model W W1 D H a b c d
6000S-3160G 450 514 400 1600 400 315 30 15
6000S-3185G
6000S-3200G
6000S-3220G
6000S-3250G 450 514 400 1800 400 315 30 15
6000S-3280G
6000S-3315G
6000S-3355G
<

Model W D H a b c d
6000S-3400G 800 550 2000 700 300 125 18
6000S-3500G

Related Names
Vector Controlled AC Inverter | Vector Frequency Inverter | Frequency Changer

Feedback Form
X